Grundfos

The Home Booster unit incorporates an integrated 200 litre storage tank, providing a usable capacity of 180 litres and complete with a Type AB air gap in full compliance with Water Byelaws regulations. This design ensures secure separation from the mains supply while maintaining a reliable and protected water reserve.

A high-grade Stainless Steel pump is fitted as standard, delivering efficient performance, consistent pressure, extended service life and low-noise operation. For properties with increased demand, or where incoming mains pressure results in slow tank replenishment, an additional 180 litre slave storage tank can be specified to expand overall capacity and improve system resilience.

Supplied with a 2 Year Warranty.

Grundfos (est. 1945) is a Danish pump manufacturer known for high-efficiency circulators, multistage boosters, borehole and wastewater pumps, plus packaged pressure systems. The range covers HVAC circulation, domestic hot water recirculation, pressure boosting, industrial water transfer and public water management, with strong focus on energy efficiency and intelligent controls.

MAGNA1 D 100-120 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D100-120F (450) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D100-120F (450) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 100-100 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D100-100F (450) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D100-100F (450) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 100-80 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D100-80F (450) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D100-80F (450) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 100-60 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D100-60F (450) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D100-60F (450) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 80-80 F

The Grundfos MAGNA1 D circulator pump is the uncomplicated option for a job well done. With its high energy efficiency, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the well-suited circulator pump for basic performance needs in applications where basic system control and monitoring are desired.

With this range of circulator pumps, everything from setup to basic control and monitoring are made straightforward. The pump is maintenance-free due to the canned-rotor type design. MAGNA1 D offers peace of mind due to the security of supply obtained by having a redundant pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between pump heads if one breaks down. The two pumps communicate wirelessly. MAGNA1 D offers the possibility of monitoring the pump via the fault relay output. The digital start and stop input remotely controls the pump. The pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main pump in both heating and cooling applications, including:

MAGNA1 D is a single-phase pump characterised by the controller and operating panel being integrated in the control box. The pump housing is available in both cast-iron and stainless-steel versions. The composite rotor can is carbon-fibre reinforced, the bearing plate and rotor cladding are made of Stainless Steel and the stator housing is made of aluminium. The power electronics are air-cooled.

The pump incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 D 80-120 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D80-120F (360) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D80-120F (360) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 80-100 F

The Grundfos MAGNA1 D circulator pump is the uncomplicated option for a job well done. With its high energy efficiency, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the well-suited circulator pump for basic performance needs in applications where basic system control and monitoring are desired.

With this range of circulator pumps, everything from setup to basic control and monitoring are made straightforward. The pump is maintenance-free due to the canned-rotor type design. MAGNA1 D offers peace of mind due to the security of supply obtained by having a redundant pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between pump heads if one breaks down. The two pumps communicate wirelessly. MAGNA1 D offers the possibility of monitoring the pump via the fault relay output. The digital start and stop input remotely controls the pump. The pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main pump in both heating and cooling applications, including:

MAGNA1 D is a single-phase pump characterised by the controller and operating panel being integrated in the control box. The pump housing is available in both cast-iron and stainless-steel versions. The composite rotor can is carbon-fibre reinforced, the bearing plate and rotor cladding are made of Stainless Steel and the stator housing is made of aluminium. The power electronics are air-cooled.

The pump incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 D 80-60 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D80-60F (360) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D80-60F (360) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 D 80-40 F

The Grundfos MAGNA1 D circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 D is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 D80-40F (360) ERP/EUP ready twin variable-speed Circulator Pump.

The Grundfos Magna1 D80-40F (360) is an energy efficient variable-speed circulator which is used primarily for one and two-pipe heating systems.

MAGNA1 circulator pump with easy selection of pump setting The pump is of the canned-rotor type, i.e.

pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid.

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 D provides peace of mind due to the security of supply obtained by having a redundant Pump, resulting in improved uptime. The flow, and thereby constant comfort, is secured because of its ability to automatically switch between Pump heads if one breaks down. The two Pumps communicate wirelessly. MAGNA1 D provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app and can also communicate via radio. MAGNA1 D can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 100-100 F

The Grundfos MAGNA1 circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 100-100F (450) ERP/EUP ready variable-speed Circulator Pump.

The Grundfos Magna1 100-100F (450) is a variable-speed circulator which is used primarily for one and two-pipe heating systems.

The Grundfos Magna1 range are energy efficient variable-speed circulators which comply with ERP/EUP European legislation.

NOTE: THIS PUMP HAS FLANGED CONNECTIONS

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app. MAGNA1 can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 100-60 F

The Grundfos MAGNA1 circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 100-60F (450) ERP/EUP ready variable-speed Circulator Pump.

The Grundfos Magna1 100-60F (450) is a variable-speed circulator which is used primarily for one and two-pipe heating systems.

The Grundfos Magna1 range are energy efficient variable-speed circulators which comply with ERP/EUP European legislation.

NOTE: THIS PUMP HAS FLANGED CONNECTIONS

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app. MAGNA1 can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

MAGNA1 100-40 F

The Grundfos MAGNA1 circulator pump is the uncomplicated option for a job to run reliably. With its high energy efficiency, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 is the well-suited circulator pump for basic performance needs in applications where basic system control and monitoring are desired.

Grundfos Magna1 100-40F (450) ERP/EUP ready variable-speed Circulator Pump.

The Grundfos Magna1 100-40F (450) is a variable-speed circulator which is used primarily for one and two-pipe heating systems.

The Grundfos Magna1 range are energy efficient variable-speed circulators which comply with ERP/EUP European legislation.

NOTE: THIS PUMP HAS FLANGED CONNECTIONS

With this range of circulator pumps, everything from setup to basic control and monitoring are made straightforward. The pump is maintenance-free due to the canned-rotor type design. MAGNA1 offers the possibility of monitoring the pump via the fault relay output. The digital start and stop input remotely controls the pump. The pump communicates wirelessly with the Grundfos GO Remote app. MAGNA1 can work as the main pump in both heating and cooling applications, including:

MAGNA1 is a single-phase pump characterised by the controller and operating panel being integrated in the control box. The pump housing is available in both cast-iron and stainless-steel versions. The composite rotor can is carbon-fibre reinforced, the bearing plate and rotor cladding are made of Stainless Steel and the stator housing is made of aluminium. The power electronics are air-cooled.

The pump incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 80-60 F

The Grundfos MAGNA1 circulator pump is the uncomplicated option for a job to run reliably. With its high energy efficiency, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 is the well-suited circulator pump for basic performance needs in applications where basic system control and monitoring are desired.

Grundfos Magna1 80-60F (360) ERP/EUP ready variable-speed Circulator Pump.

The Grundfos Magna1 80-60F (360) is a variable-speed circulator which is used primarily for one and two-pipe heating systems.

The Grundfos Magna1 range are energy efficient variable-speed circulators which comply with ERP/EUP European legislation.

NOTE: THIS PUMP HAS FLANGED CONNECTIONS

With this range of circulator pumps, everything from setup to basic control and monitoring are made straightforward. The pump is maintenance-free due to the canned-rotor type design. MAGNA1 offers the possibility of monitoring the pump via the fault relay output. The digital start and stop input remotely controls the pump. The pump communicates wirelessly with the Grundfos GO Remote app. MAGNA1 can work as the main pump in both heating and cooling applications, including:

MAGNA1 is a single-phase pump characterised by the controller and operating panel being integrated in the control box. The pump housing is available in both cast-iron and stainless-steel versions. The composite rotor can is carbon-fibre reinforced, the bearing plate and rotor cladding are made of Stainless Steel and the stator housing is made of aluminium. The power electronics are air-cooled.

The pump incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 80-120 F

The Grundfos MAGNA1 circulator Pump is the the optimal system solution. With its variable energy performance, the product complies with the EuP 2015 regulations, ensuring substantial savings on electricity. With its intuitive, user-friendly interface and maintenance-free design, MAGNA1 is the ideal circulator Pump for basic output needs in applications where basic installation management and monitoring are desired.

Grundfos Magna1 80-120F (360) ERP/EUP ready variable-speed Circulator Pump.

The Grundfos Magna1 80-120F (360) is a variable-speed circulator which is used primarily for one and two-pipe heating systems.

The Grundfos Magna1 range are energy efficient variable-speed circulators which comply with ERP/EUP European legislation.

NOTE: THIS PUMP HAS FLANGED CONNECTIONS

With this range of circulator Pumps, everything from setup to basic management and monitoring are made simple. The Pump is maintenance-free due to the canned-rotor type design. MAGNA1 provides the possibility of monitoring the Pump via the fault relay output. The digital start and stop input remotely management the Pump. The Pump communicates wirelessly with the Grundfos GO Remote app. MAGNA1 can work as the main Pump in both heating and cooling applications,

• Suitable for Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 6 Bar.
• Temperature liquid range: -10 .. 110 °C.
• Approvals include CE,VDE,EAC,MOROCCO,UKCA,TSE,RCM,UkrSEPRO

TP 100-30/4 AI-F-A-BQQE-EW3

Single-stage, close-coupled, volute (centrifugal) pump unit with in-line suction and discharge ports of identical diameter. The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is equipped with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. All pipework connection is via PN 6 DIN flanges (EN 1092-2 and ISO 7005-2). The pump is equipped with a fan-cooled asynchronous motor.

Suitable for: Commercial air conditioning