Grundfos - Unilift KP 150 A1 Submersible Pump - With Level Switch - 230v - 5m Head is a submersible pump for drainage, dewatering, and water transfer duties.

UNILIFT KP is a compact stainless-steel submersible pump designed for pumping non-aggressive water and grey water. It can be used as a portable unit or stationary installation inside and outside buildings.

UNILIFT KP is a compact stainless-steel submersible pump designed for pumping non-aggressive water and grey water. It can be used as a portable unit or stationary installation inside and outside buildings.

Stainless steel manual sump pump, max flow rate 3.8l/sec and max head 9m, 1 1/4" threaded connections and 10mm solids handling

Stainless steel sump pump with tube float switch, max flow rate 3.8l/sec and max head 9m, 1 1/4" threaded connections and 10mm solids handling.

Stainless steel sump pump with cable float switch, max flow rate 3.8l/sec and max head 9m, 1 1/4" threaded connections and 10mm solids handling.

Fitted with a suction strainer, a carrying handle and is supplied with a 5 m mains cable.

The impeller is a semi-open impeller for 10 mm free passage suitable for pumping groundwater, surface water, rain water and similar liquids.

The pump has a double shaft seal consisting of two lip seals with grease in-between.

The pump has an outer casing ensuring continuous cooling of the motor by the pumped liquid.

The rotor shaft operates in two maintenance-free carbon bearings cooled by the pumped liquid The motor is filled with a non-toxic motor liquid.

Complete with 5 metres of mains cable, with level switch. The Unilift KP is a submersible pump designed for pumping clean, non-aggressive water and slightly dirty (grey) wastewater such as domestic effluents from septic and sludge treating systems.

Stainless steel manual sump pump, max flow rate 2.3l/sec and max head 5m, 1 1/4" threaded connections and 10mm solids handling

Unilift CC9 - A1

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from

The pumps are appropriate for both stationary and portable use. They are for self-operating operation. The pumps allow free passage of particles up to ¸10 mm.

The motor incorporates self-operating overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically.

Suitable for: Commercial wastewater, Domestic wastewater, Industrial wastewater treatment and reuse

UNILIFT AP50B is a stainless-steel submersible pump designed for pumping wastewater with particles up to 50 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP50B is a stainless-steel submersible pump designed for pumping wastewater with particles up to 50 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP50B is a stainless-steel submersible pump designed for pumping wastewater with particles up to 50 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP35B.50.08.A1V
Submersible effluent pump unit

Vertical single-stage Stainless Steel submersible pump with integrated submersible 1-phase motor.

The pump is equipped with ring stand and carrying handle and is supplied with a 10 m mains cable and a level switch for self-operating start and stop.

The impeller is a VORTEX impeller for 35 mm free passage appropriate for pumping surface water, groundwater, wastewater and similar.

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil.

The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings.

The pump has Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling system.

Suitable for: Commercial wastewater, Domestic wastewater

UNILIFT AP35B is a stainless-steel submersible pump designed for pumping effluents with particles up to 35 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP35B.50.08.1V
Submersible effluent pump unit

Vertical single-stage Stainless Steel submersible pump with integrated submersible 1-phase motor.

The pump is equipped with ring stand and carrying handle and is supplied with a 10 m mains cable.

The impeller is a VORTEX impeller for 35 mm free passage appropriate for pumping surface water, groundwater, wastewater and similar.

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil.

The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings.

The pump has Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling assembly.

Suitable for: Commercial wastewater, Domestic wastewater