Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 120mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 120mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 150mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 150mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 180mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 80mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 80mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63A STEM Coolant Pump - 200mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63A STEM Coolant Pump - 300mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller and nut in nylon, pump body in aluminum, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

The Sacemi IMM63B STEM Coolant Pump - 150mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63B STEM Coolant Pump - 200mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63B STEM Coolant Pump - 250mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63B STEM Coolant Pump - 300mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: brass impeller, aluminum nut and pump body allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 90 ° C.

The Sacemi IMM71A STEM Coolant Pump - 325mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: brass impeller, aluminum nut and pump body allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 90 ° C.

The Sacemi IMM71B STEM Coolant Pump - 325mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV12 STEM Coolant Pump - 120mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.