Grundfos

TP 32-60/4 A-F-A-BUBE

Single-stage, close-coupled, volute (centrifugal) pump unit with in-line suction and discharge ports of identical diameter. The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is equipped with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. All pipework connection is via PN 6/10 DIN flanges (EN 1092-2 and ISO 7005-2). The pump is equipped with a fan-cooled asynchronous motor.

Suitable for: Commercial air conditioning

TP 32-60/2 A-F-A-BUBE

The pump unit is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is equipped with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. All pipework connection is via PN 6/10 DIN flanges (EN 1092-2 and ISO 7005-2). The pump is equipped with a fan-cooled asynchronous motor.

Suitable for: Commercial air conditioning

Grundfos TP 32-230/2 0.75kw 2900RPM Single Head Pump, 230v. Grundfos TP 32-230/2 is a single-stage, close-coupled, volute pump with in-line suction and discharge ports of identical diameter. The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is fitted with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. Pipework connection is via PN 6/10/16 DIN flanges (EN 1092-2 and ISO 7005-2). The pump is fitted with a fan-cooled asynchronous motor.

UP 20-45 N 150
The pump unit is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricatd by the pumped liquid. The pump is characterized by:

The motor is a 1-phase motor. No additional motor protection is required.

Suitable for: Commercial heating, Domestic heating, Domestic hot water recirculation

UP 20-30 N 150
The pump unit is of the canned rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricatd by the pumped liquid. The pump is characterized by:

The motor is a 1-phase motor. No additional motor protection is required.

Grundfos UP 20-30N Domestic Hot Water Service Pump Circulator, 230v.

The UP 20-30N is a Stainless Steel fixed-speed circulating pump suitable for domestic hot-water systems.

The UP 20-30N can be connected to an on/off time switch to save energy.

The on/off time switch can switch the pump on/off to limit pump operation to periods when hot water is usually required.

These pumps can be used in both open and closed systems.

Suitable for: Commercial heating, Domestic heating, Domestic hot water recirculation

MAGNA1 25-80

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 50-120 F

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 50-180 F

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA3 50-120 F

The Grundfos MAGNA3 circulator pump is the well-suited choice for almost any building project – old or new. With its unrivalled energy efficiency, all-encompassing range and built-in communication capabilities, MAGNA3 is well-suited for engineers and specifiers looking to create high-performance heating and cooling systems. The pump is maintenance-free due to the canned-rotor type design. This also means that pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. MAGNA3 features an intuitive display and allows you to connect wirelessly with the Grundfos GO Remote app, giving you access to enhanced reporting and monitoring. MAGNA3 model E has Bluetooth, which allows you to connect directly to the Grundfos GO app on your smart phone without any need for a dongle. The pump includes fieldbus communication via CIM modules as well as analogue and digital inputs and configurable relays. Control features include AUTOADAPT and FLOWADAPT. FLOWADAPT reduces the need for throttling valves, thus cutting costs on system components. MAGNA3 is the superior choice for a wide range of heating and cooling applications, including:

Suitable for: Commercial heating

TP 32-180/2 A-F-A-BQQE-EW1

Single-stage, close-coupled, volute (centrifugal) pump unit with in-line suction and discharge ports of identical diameter. The pump is of the top-pull-out design, i.e. the power head (motor, pump head and impeller) can be removed for maintenance or service while the pump housing remains in the pipework. The pump is equipped with an unbalanced rubber bellows seal. The shaft seal is according to EN 12756. All pipework connection is via PN 6/10 DIN flanges (EN 1092-2 and ISO 7005-2). The pump is equipped with a fan-cooled asynchronous motor.

Suitable for: Commercial air conditioning

MAGNA1 D 65-100 F

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

Grundfos GT-H are maintenance-free multi-purpose pressure tanks with a capacity ranging from 2 to 100 litres.
The tanks are designed for a maximum operating pressure between 10 and 16 bar and a maximum liquid temperature of 90 °C.

The tank is a steel pressure tank made of a virgin propylene liner. The tanks have a non-replaceable FDA-approved high-grade butyl diaphragm, which is pre-charged with compressed nitrogen (1.9 bar).

To ensure long-lasting durability, the diaphragm and liner are both reinforced in specific wear areas. All internal parts, including the air valve, are rounded to prevent piercing of the diaphragm in extreme conditions. The water connection uniquely provides a dual water and air seal ensuring a completely leakage-free pressure tank. Combined with booster and irrigation systems as well as thermal expansion and hydraulic hammer arrestors, the tank is appropriate for drinking-water and grey-water applications. It provides optimised comfort and a patented stainless-steel water connection. The tank also features:

MAGNA1 25-80 N

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Domestic hot water recirculation

ALPHA3 15-50/60 130

Grundfos ALPHA3 high-efficiency circulator pumps are designed for circulating liquids in heating systems. With an energy efficiency index (EEI) well below the ErP benchmark, they ensure substantial energy savings.

ALPHA3 is completely controlled with Grundfos GO Remote via Bluetooth, which gives you step-by-step assistance to pump configuration, maintenance and commissioning, including:

The pump features radiator and underfloor-heating control modes with AUTOADAPT, which continuously adjusts the pump performance to the actual heat demand, i.e. the size of the system and changing heat demand during the year. The AUTOADAPT feature finds the setting that provides optimal comfort with minimal energy consumption and makes the commissioning fast, safe, and straightforward. ALPHA3 also offers proportional-pressure, constant-pressure and constant-curve control modes with setpoint adjustment anywhere between the maximum and minimum curve of the chosen setting.

Furthermore, ALPHA3 can communicate directly with the Grundfos GO Balance app, enabling installers to easily perform hydronic balancing of radiator and underfloor-heating systems. ALPHA3 is furthermore compatible with ALPHA Reader and the Grundfos GO Balance app, enabling the installers to easily perform hydronic balancing of radiator and underfloor-heating systems.

With the self-operating night setback function, the pump automatically changes between normal duty and night setback. The changeover depends on the flow-pipe temperature controlled by the heating appliance.

The design and the chosen materials of the pump contribute to long life. The pump is self-venting through the system, which contributes to straightforward commissioning. The space-efficient design, featuring a pump head with an integrated control box, fits into most common installations. Pump and motor form an integral unit without a shaft seal. The bearings are lubricated by the pumped liquid. These constructional features ensure maintenance-free operation.

The active dry-running protection feature protects the pump against dry running during startup and normal operation. In case of a blocked rotor, the pump will continuously attempt to restart with highest possible torque.

Pump housings made of Cast Iron are electrocoated to improve corrosion resistance. The motor is a synchronous permanent-magnet/space-efficient-stator motor characterised by high efficiency. The pump speed is controlled by an integrated frequency converter incorporated in the control box.

Insulating shells are supplied with pumps to minimise heat loss in heating systems.

Suitable for: Commercial air conditioning, District heating

UPS3 15-50/65 130

High-efficiency canned-rotor circulator designed for circulating liquids in domestic heating systems. appropriate as stand-alone or integrated circulator pump in existing systems, as replacement or in new heating systems.

The pump features three control modes:

Furthermore, the speed can be controlled by a low-voltage PWM (Pulse Width Modulation) profile A – Heating.

Additionally, the straightforward and user-friendly one-button interface makes replacement and settings uncomplicated and fast.

LEDs indicate the actual operating status as well as warnings and alarms

The design of the pump and chosen materials contribute to a long service life. The pump is self-venting through the system, which contributes to straightforward commissioning. The space-efficient design, featuring a pump head with an integrated control box, fits into most common installations as well as boilers due to the ambient temperature range. Pump and motor form an integral unit without a shaft seal. The bearings are lubricated by the pumped liquid. These design features ensure maintenance-free operation. Servicing screw accessible from the front allows for straightforward access to the pump shaft if deblocking of the pump is required once it has been installed.

The pump housing is made of Cast Iron. The pump housing is electrocoated to improve corrosion resistance.

The motor is a synchronous permanent-magnet motor characterised by high efficiency. Pump speed is controlled by an integrated frequency converter incorporated in the control box.

The benchmark for the most high-efficiency circulators is EEI ≤ 0.20.

Suitable for: Commercial heating, District heating, Domestic heating

ALPHA1 15-50/60 130

Elevated-performance circulators engineered for circulating liquids in heating installations. With an energy performance index (EEI) at the ErP benchmark for most high‑performing circulators, it contributes to energy savings.

The ideal choice for basic functionality needs.

Features:

• Suitable for Commercial heating, Domestic heating, Industrial heating,
• This product's housing material is Cast Iron
• The impeller is manufactured from Composite
• Maximum operating pressure: 10 Bar.
• Temperature liquid range: 2 .. 110 °C.
• Approvals include CE,VDE,UKCA