Grundfos

Stainless steel manual sump pump, max flow rate 3.8l/sec and max head 9m, 1 1/4" threaded connections and 10mm solids handling

Stainless steel manual sump pump, max flow rate 2.3l/sec and max head 5m, 1 1/4" threaded connections and 10mm solids handling

UNILIFT AP50B is a stainless-steel submersible pump designed for pumping wastewater with particles up to 50 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP50B is a stainless-steel submersible pump designed for pumping wastewater with particles up to 50 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP35B is a stainless-steel submersible pump designed for pumping effluents with particles up to 35 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

UNILIFT AP35B is a stainless-steel submersible pump designed for pumping effluents with particles up to 35 mm. It can be installed on an auto coupling, allowing for easy maintenance and other purposes.

The Grundfos Unilift KP 250-M1 drainage pump is engineered to deliver reliable performance across a wide range of dewatering and water transfer applications. It is well suited to sump and cellar drainage, emptying tanks and swimming pools, and handling general domestic and light commercial duties where dependable operation is essential.

Built to a high specification, the pump incorporates durable Stainless Steel components to support long service life and consistent performance. Single-phase versions are equipped with an integrated automatic thermal overload protection device, safeguarding the motor against overheating in the event of dry running.

The wet rotor configuration allows the unit to tolerate short periods of dry operation without damage. An open impeller design featuring sling and bevelled-edge vanes helps minimise the risk of blockage by fibres and debris, ensuring smooth and efficient pumping in demanding conditions.

Unilift CC5 - M1

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from

The pumps are appropriate for both stationary and portable use. They are for manual operation. The pumps allow free passage of particles up to ¸10 mm.

The motor incorporates self-operating overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically.

Suitable for: Commercial wastewater, Domestic wastewater, Industrial wastewater treatment and reuse

Unilift CC7 - M1

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from

The pumps are appropriate for both stationary and portable use. They are for manual operation. The pumps allow free passage of particles up to ¸10 mm.

The motor incorporates self-operating overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically.

Suitable for: Commercial wastewater, Domestic wastewater, Industrial wastewater treatment and reuse

Unilift CC9 - M1

Grundfos Unilift CC pumps are single-stage submersible pumps with a low suction ability down to 3 mm water level. The pumps are designed for pumping rainwater and grey wastewater, e.g. from

The pumps are appropriate for both stationary and portable use. They are for manual operation. The pumps allow free passage of particles up to ¸10 mm.

The motor incorporates self-operating overload protection cutting out the motor in case of overload. When cooled to normal temperature, the motor restarts automatically.

Suitable for: Commercial wastewater, Domestic wastewater, Industrial wastewater treatment and reuse

UNILIFT AP35B.50.06.1V
Submersible effluent pump unit

Vertical single-stage Stainless Steel submersible pump with integrated submersible 1-phase motor.

The pump is equipped with ring stand and carrying handle and is supplied with a 10 m mains cable.

The impeller is a VORTEX impeller for 35 mm free passage appropriate for pumping surface water, groundwater, wastewater and similar.

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil.

The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings.

The pump has Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling assembly.

Suitable for: Commercial wastewater, Domestic wastewater

UNILIFT AP50B.50.08.1V
Submersible effluent pump unit

Vertical single-stage Stainless Steel submersible pump with integrated submersible 1-phase motor.

The pump is equipped with ring stand and carrying handle and is supplied with a 10 m mains cable.

The impeller is a VORTEX impeller for 50 mm free passage appropriate for pumping surface water, groundwater, wastewater and similar.

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil.

The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings.

The pump has Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling assembly.

Suitable for: Commercial wastewater, Domestic wastewater

UNILIFT AP50B.50.11.1V
Submersible effluent pump unit

Vertical single-stage Stainless Steel submersible pump with integrated submersible 1-phase motor.

The pump is equipped with ring stand and carrying handle and is supplied with a 10 m mains cable.

The impeller is a VORTEX impeller for 50 mm free passage appropriate for pumping surface water, groundwater, wastewater and similar.

The pump has a double shaft seal and an intermediate oil chamber pre-filled with non-toxic special oil.

The motor is insulation class F with thermal overload protection and has long-life deep-groove greased-for-life ball bearings.

The pump has Rp 2 inch discharge port and is ready for installation either free-standing or on an auto-coupling assembly.

Suitable for: Commercial wastewater, Domestic wastewater

MAGNA1 25-40

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 25-60

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating

MAGNA1 32-60 F

The Grundfos MAGNA1 is a circulator pump unit with permanent magnet motor and straightforward selection of pump setting. The MAGNA1 will fit both heating, cooling and domestic hot water circulation applications perfectly, making it the obvious choice for almost any building project – old or new.

The pump is a canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing.

The bearings are lubricated by the pumped liquid. A pump with no maintenance requirements and extremely low life cycle cost.

The pump has an intuitive user interface, which is especially fit for replacement of older circulators. The well-suited choice for basic performance needs in applications where system communication is not required.

Suitable for: Commercial heating, Commercial air conditioning, District heating, District cooling, Domestic heating, Industrial heating