Sacemi

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 120mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 150mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 2-3 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum liquid level in the tank always remains 3-4 cm lower than the support flange (see figure).

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

In cases where the liquid is particularly dirty it is advisable to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM50A STEM Coolant Pump - 80mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. This product is manufactured by Sacemi.

IMM50A 180MM 1PH

The Sacemi IMM50A Coolant Pump - 180mm - Single Phase - 230v is a Coolant Pump item. This product is manufactured by Sacemi. Voltage for this item is 230V. This is a Surface Mounted pump which can be suitable when the pump can sit in a dry, accessible location and draw liquid in via a suction pipe or hose.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV12 STEM Coolant Pump - 350mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV12 STEM Coolant Pump - 120mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 120mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 350mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 220mm - Single Phase - 230v is a Coolant Pump item. Voltage for this item is 230V.