Flamco Flexcon Expansion Vessel - 200Ltr - Engineered for EN 12828 heating and chilled-water systems, this Expansion Vessel stabilises sealed system pressure by absorbing thermal expansion in LPHW/CHW applications.

Maximum working pressure: 10.0 bar.

Vessels in accordance with EN13831.

Suitable for systems with a maximum system temperature of 120 °C.

Minimum/maximum temperature diaphragm: -10 / 90 °C.

Suitable for addition of glycol-based anti-freeze up to 50%.

A flexible rolling diaphragm with a ribbed profile prevents sticking and encourages inflow at the slightest pressure rise, while a nitrogen pre-charge helps maintain set pressure longer. The uncoated connection thread supports quick, watertight installation.

• Rolling-diaphragm design for smooth expansion control
• Nitrogen pre-charge for extended pre-pressure retention
• Top-quality steel with epoxy-powder finish
• Factory tested for reliability

Built for long service life in domestic, commercial and industrial plant rooms, with continuous medium temperatures from −10 to 70 C.

Flamco Flexcon Expansion Vessel - 1000Ltr - Engineered for EN 12828 heating and chilled-water systems, this Expansion Vessel stabilises sealed system pressure by absorbing thermal expansion in LPHW/CHW applications.

Maximum working pressure: 10.0 bar.

Vessels in accordance with EN13831.

Suitable for systems with a maximum system temperature of 120 °C.

Minimum/maximum temperature diaphragm: -10 / 90 °C.

Suitable for addition of glycol-based anti-freeze up to 50%.

A flexible rolling diaphragm with a ribbed profile prevents sticking and encourages inflow at the slightest pressure rise, while a nitrogen pre-charge helps maintain set pressure longer. The uncoated connection thread supports quick, watertight installation.

• Rolling-diaphragm design for smooth expansion control
• Nitrogen pre-charge for extended pre-pressure retention
• Top-quality steel with epoxy-powder finish
• Factory tested for reliability

Built for long service life in domestic, commercial and industrial plant rooms, with continuous medium temperatures from −10 to 70 C.

Flamco Flexcon M Expansion Vessel - 200Ltr - 3-6 bar. - Tailored for sealed heating and chilled-water systems, the Flexcon M 100/3.0 [6Bar] is a replaceable-bladder expansion vessel designed to stabilise pressure in accordance with EN 12828.

It excels where static pressure and safety-valve setpoint differ significantly, helping maintain pre-pressure while minimising cycling. Supplied ready to install with a pressure gauge and height-adjustable feet, plus an inspection flange for servicing.

• Replaceable butyl bladder for fast maintenance
• Pressure gauge and height-adjustable feet included
• Inspection flange for internal access
• Robust steel vessel with durable epoxy-powder finish
• Uncoated connection thread for easy, watertight installation

For larger models (12008000 Ltrs), a Flexvent Super can be fitted to enhance air removal.

Flamco Flexcon M Expansion Vessel - 100Ltr - 3-6 bar. - Tailored for sealed heating and chilled-water systems, the Flexcon M 100/3.0 [6Bar] is a replaceable-bladder expansion vessel designed to stabilise pressure in accordance with EN 12828.

It excels where static pressure and safety-valve setpoint differ significantly, helping maintain pre-pressure while minimising cycling. Supplied ready to install with a pressure gauge and height-adjustable feet, plus an inspection flange for servicing.

• Replaceable butyl bladder for fast maintenance
• Pressure gauge and height-adjustable feet included
• Inspection flange for internal access
• Robust steel vessel with durable epoxy-powder finish
• Uncoated connection thread for easy, watertight installation

For larger models (12008000 Ltrs), a Flexvent Super can be fitted to enhance air removal.

Built for sealed heating and chilled-water circuits, the Flexcon M [10Bar] is a replaceable-bladder expansion vessel designed to stabilise system pressure in line with EN 12828.

It excels where static pressure and safety-valve setpoint differ significantly, helping maintain pre-pressure while reducing cycling. Supplied with a pressure gauge, height-adjustable feet and an inspection flange for straightforward servicing.

• Replaceable bladder for fast maintenance and long service life
• Delivered ready to install: gauge and adjustable feet included
• Inspection flange for internal access
• Robust steel vessel with durable epoxy-powder finish

Larger Flexcon M models (12008000 Ltrs) can be fitted with a Flexvent Super for enhanced air removal.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

The 3 vessel Mainsboost 200 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The MAINSBOOST MB 1000SV-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 1000SV-1 features a nominal vessel size of 1000 litres and a pressurised cold water water storage capacity of approximately 550 litres.
Each pump is supplied with a 35mm Upstream Kit (USK) as standard.

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all MAINSBOOST vessels are supplied with a 5 year warranty.

Mains Liquid Boosting Setup

The MAINSBOOST MB 200SH-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
Supplied with a mounting cradle, these vessel systems are installed horizontally and are ideal for use under the eaves in loft spaces.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 200SH-1 features a nominal vessel size of 200 litres and a pressurised cold water water storage capacity of approximately 110 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.

Where height restrictions apply, the 2 vessel Mainsboost 200 litre horizontal steel system with 22 mm connections is ideal. Designed to installed directly onto the incoming water supply and under mains pressure fill with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Where height restrictions apply, the 3 vessel Mainsboost 200 litre horizontal steel system with 22 mm connections is ideal. Designed to installed directly onto the incoming water supply and under mains pressure fill with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The Mainsboost 200 litre vertical composite vessel with 22 mm connections is installed directly onto the incoming liquid supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property and where required can be supplied with multiple vessels options. 

The 2 vessel Mainsboost 200 litre composite steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

The 3 vessel Mainsboost 200 litre vertical composite system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

The Elbi AFV 200 Litre Vertical Accumulator Pressure Vessel - 200 Ltr - 10 bar. - Obsolete is a Pressure Vessel item. This product is manufactured by Elbi.

The accumulator vessel is a device that fitted into a pressurised water system will provide system water at a pre-set sustained pressure.

Its most common application is to supply systems in which the main supply pressure is too low and a pump is fitted to boost the pressure to an acceptable level.

As system demands take place the accumulator vessel will sustain system pressure by feeding additional water into the system at the required pressure.

This process will limit the number of times the pump needs to start (pump hunting) in order that system pressure remains at the optimal level.

The operating pressure of this is 10 bar.