Zilmet Hydro-Pro Vertical Expansion Vessel - 10 Bar. - 35Ltr Zilmet HYDRO‑PRO pressure vessels are designed for potable water and booster systems where stable pressure and efficient pump.

Zilmet Hydro-Pro Vertical Expansion Vessel - 10 Bar. - 250Ltr Zilmet HYDRO‑PRO pressure vessels are designed for potable water and booster systems where stable pressure and efficient pump.

Zilmet Cal-Pro Squared Expansion Vessel - 4 Bar. - 35Ltr Zilmet CAL‑PRO expansion vessels are designed for sealed heating systems to absorb thermal expansion as water temperature increases.

Zilmet Cal-Pro Vertical Expansion Vessel - 6 Bar. - 250Ltr Zilmet CAL‑PRO expansion vessels are designed for sealed heating systems to absorb thermal expansion as water temperature increases.

Built for sealed heating (EN 12828) and chilled-water systems, Flexcon Premium Expansion Vessels stabilise system pressure by absorbing thermal expansion so plant runs safely and efficiently.

A new TPO (thermoplastic polyolefin) diaphragm on 1235 Ltrs models delivers high flexibility and extremely low permeability, helping the pre-charge hold for longer. Lighter construction cuts material use and transport emissions; packaging is FSC-certified to reduce CO₂ impact.

• Sustainable design lighter TPO membrane uses up to 50% less material
• Long service life 15-year warranty
• Low permeability pre-charge pressure maintained for longer
• Heating & cooling suitable for LPHW and CHW installations

Vessels comply with EN 13831 and the Pressure Equipment Directive 2014/68/EU. Red epoxy powder coating (RAL 3002). Flexcon Premium 3580 are supplied with feet and a mounting kit.

Built for sealed potable hot and chilled water systems in domestic and commercial settings, these Potable Water Expansion Vessels stabilise pressure by absorbing thermal expansion for safe, reliable operation.

A nitrogen pre-charge helps retain set pressure longer, while a single threaded steel connection with plastic insert provides a durable, non-flow-through design. Suitable for central heating, cooling and tap water applications (not for solar collector circuits).

• Nitrogen gas filling for longer pre-charge retention
• Single threaded steel connection with plastic insert (no flow-through)
• Potable use supports domestic hot/chilled water
• Heating & cooling compatible for sealed systems

Designed for long service life with broad operating limits and glycol tolerance for demanding installations.

The HeatWave Vessel - Inline - 35Ltr is a Pressure Vessel item.

The HeatWave™ series hydronic expansion tanks provide quality protection for closed loop hydronic heating systems from excessive pressure due to thermal expansion.

Easy to install and featuring an incorporated hex nut connection, HeatWave™ tanks feature an air chamber sealed with a brass air valve and O-ring sealed air cap.  developed to be supported by either system piping, wall-mounted bracket (inline models) or be freestanding (vertical model with base), the HeatWave™ has a maximum working temperature of 99° C / 210° F .

The operating pressure of this is 6 bar.

• Diaphragm design
• Patented Stainless Steel (vertical models) or chromed steel (inline models) water connection

• Two-part polyurethane, epoxy primed paint finish
• Leak-free, O-ring sealed air valve cap
• Maintenance Free

Includes & Benefits

The PressureWave Vessel - Horizontal - 35Ltr is a Pressure Vessel item.

The operating pressure of this is 10 bar.

• Booster systems
• Well systems
• epoxy primed paint finish
• Leak-free, O-ring sealed air valve cap

Includes & Benefits

The PressureWave Vessel - Vertical - 35Ltr is a Pressure Vessel item.

The operating pressure of this is 10 bar.

• Booster systems
• Well systems
• epoxy primed paint finish
• Leak-free, O-ring sealed air valve cap

Includes & Benefits

The PressureWave Vessel - Inline - 35Ltr is a Pressure Vessel item.

The operating pressure of this is 10 bar.

• Booster systems
• Well systems
• epoxy primed paint finish
• Leak-free, O-ring sealed air valve cap

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

The 3 vessel Mainsboost 130 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The MAINSBOOST MB 250SV-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 250SV-1 features a nominal vessel size of 250 litres and a pressurised cold water water storage capacity of approximately 137 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all MAINSBOOST vessels are supplied with a 5 year warranty.

The 2 vessel Mainsboost 250 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

The 3 vessel Mainsboost 250 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The MAINSBOOST MB 250SH-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
Supplied with a mounting cradle, these vessel systems are installed horizontally and are ideal for use under the eaves in loft spaces.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 250SH-1 features a nominal vessel size of 250 litres and a pressurised cold water water storage capacity of approximately 137 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.