Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Purpose-built for solar thermal circuits, the Flexcon Solar 8/2.5 [8Bar] expansion vessel supports sealed systems in line with EN 12828, keeping pressure stable in high-temperature applications.

A preformed butyl rolling diaphragm with extremely low permeability helps retain pre-charge, while a nitrogen fill limits corrosion and pressure loss. The clench ring clamps the diaphragm evenly to prevent damage, and a ribbed profile avoids sticking for instant inflow. An uncoated connection thread aids watertight installation; the steel vessel is finished in a gleaming epoxy-powder coat and factory tested.

• Solar-ready expansion vessel for sealed systems
• Butyl rolling diaphragm with very low permeability
• Nitrogen pre-charge for longer pressure stability
• Clench ring construction for a robust, uniform seal

For 880 Ltrs models: both halves are coated before assembly to protect the clamp ring, and the nitrogen valve is countersunk and covered. Continuous medium temperature range −10 to 110 C.

Mains Liquid Boosting Setup

The MAINSBOOST MB 450SV-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 450SV-1 features a nominal vessel size of 450 litres and a pressurised cold water water storage capacity of approximately 248 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all MAINSBOOST vessels are supplied with a 5 year warranty.

The Mainsboost MB 450SV features a nominal vessel size of 450 litres and a pressurised water holding capacity of approximately 248 litres. 

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all Mainsboost vessels are WRAS Approved and come with a 5 year guarantee.

The Mainsboost MB 100SV-3-22 features a nominal vessel size of 3x100 litres and a pressurised water holding capacity of approximately 3x55 litres.
Each system is supplied with the new compact Mainsboost Monobloc 22/28mm Upstream Line-In Kit (ULK) as standard which significantly simplifies installation.
Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all Mainsboost vessels are WRAS Approved and come with a 5 year warranty.

The 3 vessel Mainsboost 130 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

The 3 vessel Mainsboost 200 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The MAINSBOOST MB 250SV-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 250SV-1 features a nominal vessel size of 250 litres and a pressurised cold water water storage capacity of approximately 137 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all MAINSBOOST vessels are supplied with a 5 year warranty.

The 2 vessel Mainsboost 250 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

The 3 vessel Mainsboost 250 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.

Mains Liquid Boosting Setup

The MAINSBOOST MB 300SV-1 is intended for 'direct on mains' systems (unvented hot water cylinders and combination boilers) where the incoming mains pressure is greater than 2.5 bar. but the flow is insufficient to meet demand.
MAINSBOOST vessel systems do not require an electrical supply and operate silently.

System cold water storage capacity can be expanded simply by adding one or more MAINSBOOST Add-on pumps as required. 
If the incoming mains water pressure is less than 2.5 bar., a MAINSBOOST Charger pump can be utilised in conjunction with the MAINSBOOST vessel system to boost pressure.

The MAINSBOOST MB 300SV-1 features a nominal vessel size of 300 litres and a pressurised cold water water storage capacity of approximately 165 litres.
Each pump is supplied with the unique compact MAINSBOOST Monobloc 22/28mm Upstream Kit (USK) as standard which significantly simplifies installation.

Constructed from an epoxy coated steel body and a highly durable virgin butyl diaphragm, all MAINSBOOST vessels are supplied with a 5 year warranty.

The 2 vessel Mainsboost 300 litre vertical steel system with 22 mm connections are installed directly onto the incoming water supply and under mains pressure fills with water. When the chamber is full the pump reaches a state of pressure equilibrium. The Mainsboost system now has a volume of pressurised water ready for distribution throughout the property.