-
2071094
Wilo - TOP-Z40/7 EM PN16 GG - Domestic Hot Water Circulator - 230V - Single Phase - 270 Ltr/min. - 250mmThis circulator is appropriate only for drinking water.
Can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with threaded or flange connection, preselectable speed stages for power adjustment.
Equipment and function
Manual power adjustment with 3 speed stages, Pumps with 1~ motor: P2 up to 90 W: internal protection against unacceptably high winding temperatures, and P2 = 180 W: Full motor protection with thermal winding contacts in conjunction with tripping unit.
- Pumps with 3~ motor:
P2 up to 90 W: internal protection against unacceptably high winding temperatures and P2 š¢ 180 W: Full motor protection with integrated trip electronics.
- Fault signal light
- Contact for collective fault signal
- Direction of rotation signal lamp
- Mains connection 3~, 230 V with optional switching plug
- Pump housing in red brass or grey Cast Iron (Stainless Steel depending on type)
- PN 6/PN 10 combination flange (for DN 40 to DN 65)
- Thermal insulation shells
- Additional functions by retrofittable Protect Module C:
- SSM fault signal as potential-free NC contact
- SBM run signal as potential-free NO contact
- "Overriding Off" control input via external potential-free contact (NC contact)
- Blocking detection
- Full motor protection with tripping unit
- Fault acknowledgement
- Dual pump management (two single pumps installed in parallel): Main/standby operation (automatic fault-actuated switchover/time-dependent pump cycling)
£3,658.80 RRP £2,378.22 £1,981.85
In stock
Free Standard Delivery
- Pumps with 3~ motor:
-
2070569
Wilo - TOP-Z40/7 EM PN16 RG - Domestic Hot Water Circulator - 230V - Single Phase - 270 Ltr/min. - 250mmThis circulator is suitable only for drinking water.
can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with screwed or flange connection, preselectable speed stages for power adjustment.
Equipment and function
£5,787.60 RRP £3,761.94 £3,134.95
In stock
Free Standard Delivery
-
2175523
Wilo - TOP-Z50/7 DM PN16 GG - Domestic Hot Water Circulator - 400V - Three Phase - 438 Ltr/min. - 280mmThis circulator is appropriate only for drinking water.
Can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with threaded or flange connection, preselectable speed stages for power adjustment.
Equipment and function
Manual power adjustment with 3 speed stages, Pumps with 1~ motor: P2 up to 90 W: internal protection against unacceptably high winding temperatures, and P2 š¢ 180 W: Full motor protection with thermal winding contacts in conjunction with tripping unit (optional: SK 602N/SK 622N).
- Pumps with 3~ motor:
P2 up to 90 W: internal protection against unacceptably high winding temperatures and P2 š¢ 180 W: Full motor protection with thermal winding contacts in conjunction with tripping unit (optional: SK 602N/SK 622N).
- Mains connection 3~, 230 V with optional switching plug
- Pump housing in red brass or grey Cast Iron (Stainless Steel depending on type)
- PN 6/PN 10 combination flange (for DN 40 to DN 65)
- Thermal insulation shells
£4,324.80 RRP £2,811.12 £2,342.60
In stock
Free Standard Delivery
- Pumps with 3~ motor:
-
2175524
Wilo - TOP-Z50/7 DM PN16 RG - Domestic Hot Water Circulator - 400V - Three Phase - 438 Ltr/min. - 280mmThis circulator is suitable only for drinking water.
can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with screwed or flange connection, preselectable speed stages for power adjustment.
Equipment and function
£6,480.00 RRP £4,212.00 £3,510.00
In stock
Free Standard Delivery
-
2175529
Wilo - TOP-Z65/10 DM PN16 GG - Domestic Hot Water Circulator - 400V - Three Phase - 712 Ltr/min. - 340mmThis circulator is suitable only for drinking water.
can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with screwed or flange connection, preselectable speed stages for power adjustment.
Equipment and function
£6,668.40 RRP £4,334.46 £3,612.05
In stock
Free Standard Delivery
-
2175530
Wilo - TOP-Z65/10 DM PN16 RG - Domestic Hot Water Circulator - 400V - Three Phase - 712 Ltr/min. - 340mmThis circulator is suitable only for drinking water.
can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with screwed or flange connection, preselectable speed stages for power adjustment.
Equipment and function
£8,934.00 RRP £5,807.10 £4,839.25
In stock
Free Standard Delivery
-
2175535
Wilo - TOP-Z80/10 DM PN16 GG - Domestic Hot Water Circulator - 400V - Single Phase - 1120 Ltr/min. - 360mmThis circulator is appropriate only for drinking water.
Can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with threaded or flange connection, preselectable speed stages for power adjustment.
Equipment and function
Manual power adjustment with 3 speed stages, Pumps with 1~ motor: P2 up to 90 W: internal protection against unacceptably high winding temperatures, and P2 š¢ 180 W: Full motor protection with thermal winding contacts in conjunction with tripping unit (optional: SK 602N/SK 622N).
- Pumps with 3~ motor:
P2 up to 90 W: internal protection against unacceptably high winding temperatures and P2 š¢ 180 W: Full motor protection with thermal winding contacts in conjunction with tripping unit (optional: SK 602N/SK 622N).
- Mains connection 3~, 230 V with optional switching plug
- Pump housing in red brass or grey Cast Iron (Stainless Steel depending on type)
- PN 6/PN 10 combination flange (for DN 40 to DN 65)
- Thermal insulation shells
£8,218.80 RRP £5,342.22 £4,451.85
In stock
Free Standard Delivery
- Pumps with 3~ motor:
-
2175536
Wilo - TOP-Z80/10 DM PN16 RG - Domestic Hot Water Circulator - 230V - Single Phase - 1120 Ltr/min. - 360mmThis circulator is suitable only for drinking water.
can be utilised for domestic Hot water circulation systems in the industry and building services.
Glandless circulator with screwed or flange connection, preselectable speed stages for power adjustment.
Equipment and function
£10,596.00 RRP £6,887.40 £5,739.50
In stock
Free Standard Delivery
-
2158937
Wilo - VeroTwin DP-E32/105-0,75/2-IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£8,736.00 RRP £5,678.40 £4,732.00
In stock
Free Standard Delivery
- One-button manual operation level for:
-
2159000
Wilo - VeroTwin DP-E32/105-0,75/2-R1 IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£7,980.00 RRP £5,187.00 £4,322.50
6 week lead time
Free Standard Delivery
- One-button manual operation level for:
-
2158938
Wilo - VeroTwin DP-E32/125-1,1/2-IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£8,806.80 RRP £5,724.42 £4,770.35
In stock
Free Standard Delivery
- One-button manual operation level for:
-
2159001
Wilo - VeroTwin DP-E32/125-1,1/2-R1 IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£8,052.00 RRP £5,233.80 £4,361.50
6 week lead time
Free Standard Delivery
- One-button manual operation level for:
-
2158939
Wilo - VeroTwin DP-E32/135-1,1/2-IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£8,976.00 RRP £5,834.40 £4,862.00
In stock
Free Standard Delivery
- One-button manual operation level for:
-
2159002
Wilo - VeroTwin DP-E32/135-1,1/2-R1 IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£8,220.00 RRP £5,343.00 £4,452.50
6 week lead time
Free Standard Delivery
- One-button manual operation level for:
-
2158940
Wilo - VeroTwin DP-E32/135-1,5/2-IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£10,443.60 RRP £6,788.34 £5,656.95
In stock
Free Standard Delivery
- One-button manual operation level for:
-
2159003
Wilo - VeroTwin DP-E32/135-1,5/2-R1-IE4 Centrifugal Pump - 380v - Three Phase - 10 Bar. - 260mmGlanded twin-head pump with in line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things. Three-phase AC motor with frequency converter
Product detail:
Single-stage low-pressure Centrifugal Pump with one-piece shaft, Spiral housing, in line design, PN 16 flange Ä drilled according to EN 1092-2, Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor), Pump housing and motor flange with cataphoretic coating as standard, and Mechanical seal for water feed up to T=120 ∞C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 ∞C. Other mechanical seals or other fluids/temperatures on request..
Accessories:
Mounting brackets for fixing to the foundation, IR-Monitor, IF module PLR, IF module LON, IF module Modbus, IF module BACnet, IF module CAN, and Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1.
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for displaying:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional Product Functions:
- Interfaces: Control input "Overriding Off", "External pump cycling" (effective only in dual pump operation), analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0Ä10 V, 2Ä10 V, 0Ä20 mA, 4Ä20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR-Stick/IR-Monitor, plug-in position for Wilo - IF-Module Modbus, BACnet, CAN, PLR, LON for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
- Adjustable time interval for pump cycling (in dual pump mode)
- Integrated full motor protection
- Different operating modes for heating mode (HV) or air-conditioning mode (AC)
- Access disable
- Different operation levels: Standard / Service
£9,687.60 RRP £6,296.94 £5,247.45
In stock
Free Standard Delivery
- One-button manual operation level for:
Wilo
(12151 products)
Filters Products
Filters Products