Wilo

The Wilo - Comfort twin pump pressurisation units (duty / standby) are engineered for use on heating or chilled water systems up to and including 3.5 bar. Cold fill pressures.

The unit is fitted with an 18 litre polypropylene break tank c/w type AB air gap to BS13077:2008 and water regulations 1999, Wras approved equilibrium ball float valve to BS1212 and a low water float switch and strainers for pump protection.

Each pump is fitted with a non return valve and quick release couplings for ease of maintenance. The pressure transducer monitors the system pressure and feeds a 0-10v signal to the comfort controller.

Comfort Controller is complete with the following incorporates:

User friendly interface that has a 2 line LCD backlight display, Healthy / fail LED, Password protection, System Fill for initial fill of system, Pump check routine, that runs both pumps for 2 seconds if inactive for 7-90 days, Pump trip and fail alarms, System leak alarm, Excessive starts alarm, Alarm log, Hours Run, Automatic duty rotation, and Connectivity: BACnet = RS485 interface, BACnet MS/TP protocol.

2 wire BACnet

Volt Free Contacts are supplied with terminals for common, normally open and normally closed.

(5A, 230V)

Pump no.1 trip, Pump no. 1 run, Pump no.2 trip, Pump no. 2 run, High Pressure, Low Pressure, Excess starts, Low water and Boiler Interlock (NC only)

(10A, 230V)

To be selected from Power fail, Common alarm, Common pressure alarm

Standards Applied:

Low Voltage and Machinery Directive 2006/42/EC, EMC Directive EMC 2004/108/EC, BSEN809, BS7074-1 to 3, BS13077:2008 and water regulations 1999.

The Wilo - Comfort twin pump pressurisation units (duty / standby) are engineered for use on heating or chilled water systems up to and including 3.5 bar. Cold fill pressures.

The unit is fitted with an 18 litre polypropylene break tank c/w type AB air gap to BS13077:2008 and water regulations 1999, Wras approved equilibrium ball float valve to BS1212 and a low water float switch and strainers for pump protection.

Each pump is fitted with a non return valve and quick release couplings for ease of maintenance. The pressure transducer monitors the system pressure and feeds a 0-10v signal to the comfort controller.

Comfort Controller is complete with the following incorporates:

User friendly interface that has a 2 line LCD backlight display, Healthy / fail LED, Password protection, System Fill for initial fill of system, Pump check routine, that runs both pumps for 2 seconds if inactive for 7-90 days, Pump trip and fail alarms, System leak alarm, Excessive starts alarm, Alarm log, Hours Run, Automatic duty rotation, and Connectivity: BACnet = RS485 interface, BACnet MS/TP protocol.

2 wire BACnet

Volt Free Contacts are supplied with terminals for common, normally open and normally closed.

(5A, 230V)

Pump no.1 trip, Pump no. 1 run, Pump no.2 trip, Pump no. 2 run, High Pressure, Low Pressure, Excess starts, Low water and Boiler Interlock (NC only)

(10A, 230V)

To be selected from Power fail, Common alarm, Common pressure alarm

Standards Applied:

Low Voltage and Machinery Directive 2006/42/EC, EMC Directive EMC 2004/108/EC, BSEN809, BS7074-1 to 3, BS13077:2008 and water regulations 1999.

• Permitted temperature range -20 ∞C to +130 ∞C, for short periods (2 h) to +140 ∞C (TOP-S 25/13, 80/15, 80/20: -20 ∞C to +110 ∞C)
• Mains connection:
• 1~230 V, 50 Hz (depending on type)
• 3~230 V, 50 Hz (with optional switching plug)
• 3~400 V, 50 Hz
• Protection class IP X4D
• Screwed connection or flange connection (depending on type) Rp 1 to DN 100
• Max. operating pressure of standard version: 6/10 bar. or 6 bar. (special version: 10 bar.)