Sacemi

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

The Sacemi SPV12 STEM Coolant Pump - 170mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. This product is manufactured by Sacemi. The hydraulic components, namely the impeller, scroll and pump body in PBT allow the pumps to be applied with water, emulsions and oily substances in general with a maximum viscosity of 3° Engler (21 CST). The temperature of the liquid must not exceed 70° C.

The Sacemi SPV12 STEM Coolant Pump - 270mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV12 STEM Coolant Pump - 350mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV12 STEM Coolant Pump - 90mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

The Sacemi SPV18 STEM Coolant Pump - 120mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller, scroll and pump body in PBT, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

The Sacemi SPV18 STEM Coolant Pump - 170mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 220mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 270mm - 3 Phase - 415v is a Coolant Pump item.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. This product is manufactured by Sacemi. The hydraulic components, namely the impeller, scroll and pump body in PBT allow the pumps to be applied with water, emulsions and oily substances in general with a maximum viscosity of 3° Engler (21 CST). The temperature of the liquid must not exceed 70° C.

The Sacemi SPV18 STEM Coolant Pump - 350mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 3-4 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of the liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi SPV18 STEM Coolant Pump - 90mm - 3 Phase - 415v is a Coolant Pump item.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM71B STEM Coolant Pump - 250mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. This product is manufactured by Sacemi. The hydraulic components, namely the nylon impeller and scroll and the aluminium pump body allow the pumps to be applied with water, emulsions and oily substances in general with a maximum viscosity of 3° Engler (21 CST). The temperature of the liquid must not exceed 90° C.

The Sacemi IMM63A STEM Coolant Pump - 250mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

The Sacemi IMM63A STEM Coolant Pump - 150mm - 3 Phase - 415v is a Coolant Pump item. Voltage for this item is 415V.

Usual installation is onto a tank with a capacity proportionate to the flow rate, about 4-5 cm from the bottom. This product is manufactured by Sacemi. It is important to check that the maximum level of liquid in the tank always remains 3-4 cm lower than the support flange (see figure). In cases where the liquid is particularly dirty, it is recommended to build the tank with compartments, to allow the deposit of sludge before it is fished out by the pump. For different uses it is advisable to consult our Technical Department.

They are suitable for the transfer of liquids containing impurities up to 3 mm in size.

The hydraulic components: impeller and nut in PTB, pump body in Cast Iron, allow it to be used with water, emulsions and oily substances in general, with a viscosity not exceeding 21 cSt (3 ° Engel).

The liquid temperature must not exceed 70 ° C.

The Sacemi SP 50-350mm Coolant Pump is a Coolant Pump item. This is a Surface Mounted pump which can be suitable when the pump can sit in a dry, accessible location and draw liquid in via a suction pipe or hose.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. The Sacemi IMM80B Coolant Pump - 200mm - 3 Phase - 415v is a Coolant Pump item.

The pumps are appropriate to transfer liquids containing impurities measuring up to 2-3 mm. This product is manufactured by Sacemi.